Introduction to Stick type heat treatment furnace, how much is the price of the Forging furnace?

Stick type heat treatment furnaceIt is a kind of equipment which uses gas as fuel and is specially used for heating metal before forging.，the advantage is It has the advantages of high heating efficiency, high energy utilization, accurate temperature control, good environmental protection performance, simple operation and strong adaptability.、Suitable for forging and heating of various metal materials, including steel, aluminum and copper. At the same time, it can also be used in metal heat treatment, tempering and other technological processes.、The use of clean and environmentally friendly natural gas as fuel effectively avoids the adverse effects of chemical reactions between impurities such as coal-fired furnaces and forgings during heating. At the same time, natural gas has high calorific value and high combustion temperature, and the combustion temperature can be further increased by preheating air and fuel. In addition, the gas forging heating furnace also has good heat loss control ability and intelligent control system, which can accurately adjust the ratio of air to natural gas, ensure full combustion of natural gas, and reduce mechanical incomplete combustion and chemical incomplete combustion.、Natural gas is used as a heat source, resulting in less waste gas and smoke after combustion, and less pollution to the environment. This will help reduce industrial emissions and improve the atmospheric environment.、Adopting advanced combustion technology and materials, it has a long service life and low maintenance cost.，the product looks beautiful.，The high-temperature flame and flue gas generated by burning gas (such as natural gas and liquefied petroleum gas) in the furnace are used as heat sources to heat metal materials.，Commonly used inMetal heat treatment,Metal forging heating,Metal melting and casting,Energy conservation and environmental protection,Improve production efficiency and so on。The following is to introduce the Stick type heat treatment furnace:

1、Brief introduction of Stick type heat treatment furnace

Stick type heat treatment furnaceIt is an important heating equipment before metal forging. It uses natural gas as fuel to heat metal materials through high-temperature flame and smoke generated by combustion to meet the requirements of forging process.，Usually equipped with intelligent control system, it can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.、It can improve the plasticity and fluidity of metal materials, reduce the difficulty and cost of forging, and improve product quality and production efficiency.、The metal material can be heated to the required temperature in a short time, and the production efficiency is improved.、Uniform heating and precise control can be realized, so it is helpful to improve the product quality and yield of metal materials.、Using regenerative combustion system or advanced burner design can realize the uniform distribution of temperature in the furnace, ensure the uniform heating of metal materials and improve product quality.，the product looks atmospheric.。

Stick type heat treatment furnace

2、Stick type heat treatment furnace application

Stick type heat treatment furnaces have the following purposes.

1. Metal heat treatment

In addition to forging heating, Stick type heat treatment furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

2. Metal forging heating

The Stick type heat treatment furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

3. Metal melting and casting

Although it is mainly used for forging heating, some types of Stick type heat treatment furnaces can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

4. Energy conservation and environmental protection

The Stick type heat treatment furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

5. Metal heat treatment

In addition to forging heating, Stick type heat treatment furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

Stick type heat treatment furnace

3、Structural advantages of Stick type heat treatment furnace

The Stick type heat treatment furnace has the following structure

1. Waste heat recovery system

Recover the waste heat in the exhaust gas of heating furnace to improve the energy utilization efficiency.

2. Radiation chamber

The heat load of the main place for Stick type heat treatment furnace heat exchange accounts for about 70%-80% of the whole furnace. The furnace tube in the radiation room conducts heat through flame or high-temperature flue gas, which is mainly radiant heat, so it is called radiation tube.

3. ventilation system

Ensure the gas flow in the furnace and maintain the stability of the atmosphere and temperature in the furnace.

4. Waste heat recovery system

Used to recover the exhaust heat of the heating furnace. There are two kinds of recovery methods, one is to recover by preheating combustion air, so that the recovered heat can return to the furnace again; The other is to use another recovery system to recover heat. The former is called air preheating mode, and the latter is usually called waste heat boiler mode.

5. furnace chamber

A space for holding metallic materials for heating.

Stick type heat treatment furnace

4、Working principle of Stick type heat treatment furnace

Stick type heat treatment furnaceat runtime,Heat of combustion based on fuel. Natural gas is sprayed from the burner, mixed with combustion-supporting air and burned to produce high-temperature flame and smoke. These high-temperature flames and smoke transfer heat to the metal materials in the furnace by radiation and convection, so that they gradually heat up to the temperature required for forging.，is a kind of high quality and low price Stick type heat treatment furnace，the product looks atmospheric.。

Stick type heat treatment furnace

5、Stick type heat treatment furnace function

Stick type heat treatment furnaceit has the functions of Casting heating, hardening and tempering, Forging heating, normalizing and quench，is a Stick type heat treatment furnace，It is a kind of heating equipment using natural gas as fuel, which is mainly used to heat metal materials to the required forging temperature in a short time.，be loved by our customers.。

Stick type heat treatment furnace

6、One-combustion energy saving workshop real shot

You can buy Stick type heat treatment furnace according to your needs and show you product videos.。

Stick type heat treatment furnace

As you can see from the live video.One-combustion energy saving features include energy saving and environmental protection, Strong adaptability, Easy to control, Easy to maintain and energy-efficient。

Stick type heat treatment furnacethe product looks beautiful.，multifunctional, with functions such as hardening and tempering, Casting heating, anneal, heat treatment and temper，It is an efficient, energy-saving and environment-friendly metal heating device.。