Introduction to Fully automatic heat treatment furnace, advantages, characteristics and principles of heating furnace

Fully automatic heat treatment furnaceIt is a kind of equipment which uses gas as fuel and is specially used for heating metal before forging.，features include Easy to maintain, Strong adaptability, Easy to control, Stable and reliable and Strong adaptability，it mainly includes recovery of waste heat, convection chamber, ventilation system, Radiation chamber and combustor，productThe overall structural design is simple and novel.，is a kind of Fully automatic heat treatment furnace manufactured by One-combustion energy saving。The following is to introduce the Fully automatic heat treatment furnace:

1、Brief introduction of Fully automatic heat treatment furnace

Fully automatic heat treatment furnaceIt is a kind of equipment that uses natural gas as fuel to heat metal materials and make them reach forging temperature.，reliable quality。

Fully automatic heat treatment furnace

2、Fully automatic heat treatment furnace characteristics

The Fully automatic heat treatment furnace features are as follows:

1. Easy to control

By adjusting the burner and ventilation system, the temperature and atmosphere in the furnace can be accurately controlled to meet the heating requirements of different metal materials.

2. Easy to maintain

The structural design of the Fully automatic heat treatment furnace is reasonable and easy to maintain, which reduces the operating cost and failure rate of the equipment.

3. Easy to control

The combustion system and ventilation system of the Fully automatic heat treatment furnace can be adjusted as required to accurately control the temperature and atmosphere in the furnace and meet the heating requirements of different metal materials.

4. energy saving and environmental protection

Natural gas is a kind of clean energy, which produces less waste gas and waste smoke after combustion and has little environmental pollution. At the same time, through wall regenerative combustion technology, flue gas waste heat recovery system and other technical means, the Fully automatic heat treatment furnace further improves energy utilization efficiency and reduces energy consumption and emissions.

5. Efficient heating

The Fully automatic heat treatment furnace can heat the metal to the required forging temperature in a very short time, reducing the loss caused by the oxidation of the metal.

Fully automatic heat treatment furnace

3、Functional advantages of Fully automatic heat treatment furnace

The advantages of Fully automatic heat treatment furnace are as follows:

1. Extend the service life of equipment

The Fully automatic heat treatment furnace adopts advanced combustion technology and materials, which has a long service life and low maintenance cost.

2. Improve product quality

Because the Fully automatic heat treatment furnace can realize uniform heating and precise control, it is helpful to improve the product quality and yield of metal materials.

3. Intelligent control

The Fully automatic heat treatment furnace is usually equipped with an intelligent control system, which can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.

4. Multiple fuel options

Although the Fully automatic heat treatment furnace mainly uses natural gas as fuel, some equipment also supports other types of gas or liquid fuel, which has strong fuel adaptability.

5. easy to operate

The operation interface of the Fully automatic heat treatment furnace is friendly and easy for operators to use. At the same time, the equipment also has the function of fault diagnosis and alarm, which can find and deal with abnormal situations in time.

Fully automatic heat treatment furnace

4、Fully automatic heat treatment furnace use

The purpose of Fully automatic heat treatment furnace is introduced as follows:

1. Metal heat treatment

In addition to forging heating, Fully automatic heat treatment furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

2. Metal tempering

By properly heating and cooling the metal material, the Fully automatic heat treatment furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

3. Metal forging heating

The Fully automatic heat treatment furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

4. Metal heat treatment

In addition to forging heating, Fully automatic heat treatment furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

5. Metal forging heating

The Fully automatic heat treatment furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

Fully automatic heat treatment furnace

5、Advantages of Fully automatic heat treatment furnace principle

Fully automatic heat treatment furnacethe principle is simple.The high-temperature flame and flue gas generated by burning gas (such as natural gas and liquefied petroleum gas) in the furnace are used as heat sources to heat metal materials.，it is usually composed of Radiation chamber, ventilation system, combustor, convection chamber and Radiation chamber，This Fully automatic heat treatment furnaceThe overall structural design is simple, diverse and beautiful.，it has the functions of quench, normalizing, anneal, Casting heating and Forging heating，it is an ideal choice for customers to buy Fully automatic heat treatment furnace。

Fully automatic heat treatment furnace

6、Fully automatic heat treatment furnace price consultation

The Fully automatic heat treatment furnace price is introduced as follows:

1. product costs

The production cost is mainly the purchase of raw materials. One-combustion energy saving attaches great importance to the purchase of raw materials to ensure the comprehensive quality of products. Only excellent raw materials can produce excellent products, and the input cost of raw materials has a direct relationship with the formulation of product prices. Under the premise of ensuring excellent product performance, One-combustion energy saving strives to reduce the input cost of products, and customers are very satisfied with this.

2. Reasonable cost

Product manufacturers are different, and the cost spent by each manufacturer in producing products is definitely different. The higher the cost of producing products, the higher the price of products set by manufacturers. On the contrary, the Fully automatic heat treatment furnace price is low.

3. market competition

This factor is directly related to the economic dynamics. When the economic dynamics are unstable, the relationship between supply and demand will be unbalanced, which will lead to a very large fluctuation in the price of Fully automatic heat treatment furnace. Therefore, we should also be aware of the relationship between this factor and the price during the price setting process.

4. marketing channel

Manufacturers mainly implement the sales mode of small profits but quick turnover and online direct sales. The prices of products are generally low, and the prices are clearly marked, and they will not be more expensive at will. In addition, manufacturers mainly establish communication and negotiation relations with customers through the Internet and telephone, which can greatly reduce the investment in facade expenses, and the production cost of manufacturers is low, so the price of Fully automatic heat treatment furnace is low.

5. Manufacturer's strength

One-combustion energy saving's scale and strength are relatively strong, the technology and technology of products produced by manufacturers are relatively advanced, and there is less waste of resources in the process of manufacturing, and the price of products will be relatively low.

Fully automatic heat treatment furnace

Fully automatic heat treatment furnaceThe structural design is simple, novel and special.，it is mainly composed of furnace chamber, ventilation system, recovery of waste heat, furnace chamber and ventilation system，is a popular Fully automatic heat treatment furnace，the product looks atmospheric.。