Introduction to Regenerative walking heat treatment furnace and Forging furnace structure principle

Regenerative walking heat treatment furnaceIt is an efficient, energy-saving and environment-friendly metal heating device.，is a common Regenerative walking heat treatment furnace，it has the functions of temper, Casting heating, normalizing, Forging heating and temper。The following is to introduce the Regenerative walking heat treatment furnace:

1、Brief introduction of Regenerative walking heat treatment furnace

Regenerative walking heat treatment furnaceIt is a forging heating device using gas as fuel.，be loved by our customers.。

Regenerative walking heat treatment furnace

2、Functional advantages of Regenerative walking heat treatment furnace

Regenerative walking heat treatment furnaces have the following advantages.

1. Intelligent control

The Regenerative walking heat treatment furnace is usually equipped with an intelligent control system, which can automatically adjust the parameters such as gas supply and air flow according to the heating demand, and realize accurate control of the temperature and atmosphere in the furnace.

2. Rapid temperature rise

The Regenerative walking heat treatment furnace can heat the metal material to the required temperature in a short time, which improves the production efficiency.

3. Reduce operating costs

The efficient combustion and waste heat recovery system of the Regenerative walking heat treatment furnace can significantly reduce energy consumption, thus reducing operating costs.

4. Extend the service life of equipment

The Regenerative walking heat treatment furnace adopts advanced combustion technology and materials, which has a long service life and low maintenance cost.

5. Uniform heating

The Regenerative walking heat treatment furnace adopts regenerative combustion system or advanced burner design, which can realize uniform distribution of temperature in the furnace, ensure uniform heating of metal materials and improve product quality.

Regenerative walking heat treatment furnace

3、Regenerative walking heat treatment furnace HD real shot

A high-definition picture list of Regenerative walking heat treatment furnace is available for our customers to visit. The physical visit can be made to the factory. The address of the visit is Jinan, Shandong province, and the time can be reserved in advance. The manufacturer has a special person to receive it.。

Regenerative walking heat treatment furnace

Note: All the pictures in this article were taken by One-combustion energy saving manufacturer.。

4、Introduction of Regenerative walking heat treatment furnace characteristics

Regenerative walking heat treatment furnace has the following characteristics

1. Stable and reliable

The Regenerative walking heat treatment furnace has a stable combustion system and temperature control system, which can ensure the uniformity and stability of the temperature in the furnace, thus improving the quality and production efficiency of forged products.

2. Easy to control

By adjusting the burner and ventilation system, the temperature and atmosphere in the furnace can be accurately controlled to meet the heating requirements of different metal materials.

3. energy saving and environmental protection

Natural gas is a kind of clean energy, which produces less waste gas and waste smoke after combustion and has little environmental pollution. At the same time, through wall regenerative combustion technology, flue gas waste heat recovery system and other technical means, the Regenerative walking heat treatment furnace further improves energy utilization efficiency and reduces energy consumption and emissions.

4. Efficient heating

The Regenerative walking heat treatment furnace can heat the metal material to the required temperature in a short time and improve the production efficiency.

5. Easy to maintain

The structural design of the Regenerative walking heat treatment furnace is reasonable and easy to maintain, which reduces the operating cost and failure rate of the equipment.

Regenerative walking heat treatment furnace

5、Regenerative walking heat treatment furnace structure composition

The Regenerative walking heat treatment furnace has the following structure

1. Waste heat recovery system

Recover the waste heat in the exhaust gas of heating furnace to improve the energy utilization efficiency.

2. convection chamber

The high-temperature flue gas discharged from the radiation chamber is used for convective heat transfer to further heat the metal materials.

3. combustor

The device that mixes natural gas with combustion-supporting air and ejects it is the core component of the heating furnace.

4. furnace chamber

A space for holding metallic materials for heating.

5. Radiation chamber

The heat load of the main place for Regenerative walking heat treatment furnace heat exchange accounts for about 70%-80% of the whole furnace. The furnace tube in the radiation room conducts heat through flame or high-temperature flue gas, which is mainly radiant heat, so it is called radiation tube.

Regenerative walking heat treatment furnace

6、One-combustion energy saving introduced

One-combustion energy saving is a strong and professional Regenerative walking heat treatment furnace manufacturer, with advanced Regenerative walking heat treatment furnace production technology and rich production experience. It will not only provide users with Regenerative walking heat treatment furnace with Stable and reliable, but also provide users with complete pre-sales, in-sales and after-sales services for the benefit of users. Welcome new and old users to visit and buy.。

One-combustion energy saving

Regenerative walking heat treatment furnaceIt has a wide range of uses, including Metal forging heating, Improve production efficiency, Metal tempering, Metal melting and casting and Metal tempering，it is widely used in machinery, material, electron, automobile, war industry and other industries。