What is a SCR low-temperature denitrification? SCR denitration specifications, models, and parameters

SCR low-temperature denitrificationthat is, selective catalytic reduction technology is a technology used to reduce the emission of nitrogen oxides in flue gas.，it is usually composed of Catalyst reactor, Catalyst supply system, control system, Flue gas mixing and distribution system and Temperature control and monitoring system，This productThe structure is novel, special, advanced, reasonable and scientific.，It is famous for its high-efficiency denitration ability, which can usually reach more than 90% denitration efficiency. This means that the SCR low-temperature denitrification technology can significantly reduce the concentration of nitrogen oxides (NOx) in flue gas and make it meet strict environmental protection emission standards. This high-efficiency denitration ability is mainly due to the promotion of the catalyst, which makes the chemical reaction between reductant and NOx more rapid and thorough.、There are many kinds of catalysts used in the technology, including vanadium-based catalysts and titanium-based catalysts, which can promote the chemical reaction between reductant and NOx at a lower temperature. At the same time, the active components and carrier materials of the catalyst are constantly being developed and improved to improve its catalytic efficiency and service life. This enables the SCR low-temperature denitrification technology to maintain efficient denitrification capability in a wider temperature range and more complex flue gas conditions.、Intelligent control is gradually realized. By integrating advanced control system and sensor technology, the SCR low-temperature denitrification can monitor the composition and emission concentration of flue gas in real time, and automatically adjust the injection amount of reductant and the active state of catalyst to ensure the stability and reliability of denitrification efficiency.、The by-products produced by the technology are mainly nitrogen and water vapor, which are harmless to the environment and will not cause secondary pollution. Compared with the traditional wet flue gas denitrification technology, the SCR low-temperature denitrification technology does not need to use a lot of water resources and will not produce pollutants such as wastewater, which is more in line with the requirements of environmental protection and sustainable development.、Technology has been developed and applied for many years, and it is mature and stable. The SCR low-temperature denitrification has high reliability and stability, and can maintain stable denitrification efficiency under various working conditions. In addition, the SCR low-temperature denitrification technology has good adaptability and adjustability, and can be adjusted and optimized according to different flue gas components and emission requirements.。The following is to introduce the SCR low-temperature denitrification:

1、Brief introduction of SCR low-temperature denitrification

SCR low-temperature denitrificationis an efficient, stable and environment-friendly flue gas denitrification technology.，is a SCR low-temperature denitrification，It is mostly used in environmental protection, Improve product quality, Flue gas denitrification, environmental protection, Promote sustainable development, Meet the requirements of environmental protection and so on，has been favored by more and more customers.。

SCR low-temperature denitrification

2、Functional advantages of SCR low-temperature denitrification

SCR low-temperature denitrifications have the following advantages.

1. economic viability

The initial investment of this technology may be high, but in the long run, its economic feasibility is remarkable. The high-efficiency denitration ability of SCR low-temperature denitrification technology can significantly reduce the environmental emission cost of enterprises and avoid fines and legal risks due to illegal emissions. In addition, SCR low-temperature denitrification technology can also reduce operating costs and improve the economic benefits of enterprises by recycling heat energy.

2. Intelligent control and convenience of operation

The SCR low-temperature denitrification has gradually realized intelligent control. By integrating advanced control system and sensor technology, the SCR low-temperature denitrification can monitor the composition and emission concentration of flue gas in real time, and automatically adjust the injection amount of reductant and the active state of catalyst to ensure the stability and reliability of denitrification efficiency.

3. Diversity and high efficiency of catalysts

There are many kinds of catalysts used in the SCR low-temperature denitrification technology, including vanadium-based catalysts and titanium-based catalysts, which can promote the chemical reaction between reductant and NOx at low temperature. At the same time, the active components and carrier materials of the catalyst are constantly being developed and improved to improve its catalytic efficiency and service life. This enables the SCR low-temperature denitrification technology to maintain high efficiency of denitration in a wider temperature range and more complex flue gas conditions.

4. High efficiency denitration capacity

Gate is famous for its high efficiency of denitration, which can usually reach more than 90% denitration efficiency. This means that the SCR low-temperature denitrification technology can significantly reduce the concentration of nitrogen oxides (NOx) in flue gas and make it meet strict environmental protection emission standards. This high-efficiency denitration ability mainly benefits from the promotion of catalyst, which makes the chemical reaction between reductant and NOx more rapid and thorough.

5. Environmental friendliness

The by-products produced by SCR low-temperature denitrification technology are mainly nitrogen and water vapor, which are harmless to the environment and will not cause secondary pollution. Compared with the traditional wet flue gas denitrification technology, the SCR low-temperature denitrification technology does not need to use a lot of water resources and will not produce pollutants such as wastewater, which is more in line with the requirements of environmental protection and sustainable development.

SCR low-temperature denitrification

3、Introduction of SCR low-temperature denitrification characteristics

SCR low-temperature denitrification has the following characteristics

1. Small secondary pollution

The by-products produced in the SCR low-temperature denitrification opening process are nitrogen and water vapor, and there is no secondary pollution problem.

2. selectivity

Under the action of catalyst, the reducing agent mainly reacts with NOx selectively, but less with other components (such as oxygen) in flue gas, thus reducing unnecessary consumption.

3. high efficiency

Gate technology can effectively remove NOx from flue gas, and the denitrification efficiency can usually reach more than 90%.

4. Strong adaptability

SCR low-temperature denitrification technology can meet the needs of flue gas denitrification under different working conditions and has a wide range of applications.

5. energy saving and environmental protection

This technology can effectively reduce NOx emission in flue gas, reduce environmental pollution, and at the same time, it has stable operation and low energy consumption, which meets the requirements of energy saving and environmental protection.

SCR low-temperature denitrification

4、SCR low-temperature denitrification application

SCR low-temperature denitrificationMainly used forImprove product quality,Promote sustainable development,Flue gas denitrification,Improve product quality andMeet the requirements of environmental protection，The structural design is simple, novel and special.，the main structure includes Temperature control and monitoring system, control system, Flue gas mixing and distribution system, Catalyst reactor, Catalyst supply system and so on。

SCR low-temperature denitrification

5、How much is the SCR low-temperature denitrification?

The SCR low-temperature denitrification price is introduced as follows:

1. product function

The more functions a product has, the higher its manufacturing cost, so that the product can be used by customers as much as possible, which can create more useful value for customers, so the price will be higher.

2. product costs

One-combustion energy saving has a large production scale, strong manufacturing strength and high degree of automation in product production. In such a manufacturing environment, the cost of manufacturing SCR low-temperature denitrification in One-combustion energy saving is greatly reduced.

3. market supply and demand

Market change is the main factor that affects the price level. Because of the instability and uncertainty of the market, the sales price of SCR low-temperature denitrification will fluctuate greatly, and the market changes are various.

4. Company size

The nature of the manufacturer can also greatly affect the price of the SCR low-temperature denitrification. General manufacturers are divided into direct sellers, agents and middlemen. If they are direct selling manufacturers, there are not too many intermediate links, and their sales prices are low.

5. Parameter size

Because the specifications and models of products are different, their specifications and configurations are not the same. As we all know, the cost of products with high configuration will be higher, and vice versa, because there is a close relationship between product sales price and specifications and models.

SCR low-temperature denitrification

6、One-combustion energy saving delivery site

On-site aerial photography of SCR low-temperature denitrification。

SCR low-temperature denitrification

As you can see from the live video.One-combustion energy saving features include energy saving and environmental protection, Less secondary pollution, Mature technology, High denitration efficiency and Stable operation。

SCR low-temperature denitrificationmultifunctional, with functions such as environmental protection, Improve energy efficiency, Promote sustainable development, Improve working conditions and environmental protection，it is widely used in coal-fired power station, iron and steel plant, metallurgy, building materials and coal-fired power station，it is mainly composed of Catalyst reactor, Catalyst supply system, Flue gas mixing and distribution system, Temperature control and monitoring system and control system。