What is a Natural gas regenerative through furnace? heating furnace specifications, models, and parameters

Natural gas regenerative through furnaceIt is a forging heating device using gas as fuel.，is a Natural gas regenerative through furnace newly developed by One-combustion energy saving。The following is to introduce the Natural gas regenerative through furnace:

1、Brief introduction of Natural gas regenerative through furnace

Natural gas regenerative through furnaceIt is a kind of equipment that uses natural gas as fuel to heat metal materials and make them reach forging temperature.，Widely used inImprove production efficiency,Metal melting and casting,Improve production efficiency,Metal forging heating,Energy conservation and environmental protection and so on，is developed and improved by One-combustion energy saving。

Natural gas regenerative through furnace

2、Natural gas regenerative through furnace application

Natural gas regenerative through furnaces have the following purposes.

1. Metal melting and casting

Although it is mainly used for forging heating, some types of Natural gas regenerative through furnaces can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

2. Metal tempering

By properly heating and cooling the metal material, the Natural gas regenerative through furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

3. Improve production efficiency

The Natural gas regenerative through furnace has the advantages of fast heating speed and accurate temperature control, which can improve production efficiency. This is especially important for mass-produced forging workshops.

4. Energy conservation and environmental protection

The Natural gas regenerative through furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

5. Metal heat treatment

In addition to forging heating, Natural gas regenerative through furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

Natural gas regenerative through furnace

3、Physical picture of Natural gas regenerative through furnace

The Natural gas regenerative through furnace has a beautiful appearance and atmosphere for our customers' reference.。

Natural gas regenerative through furnace

Note: All the pictures in this article were taken by One-combustion energy saving manufacturer.。

4、Introduction of advantages of Natural gas regenerative through furnace

Natural gas regenerative through furnaces have the following advantages.

1. easy to operate

The operation interface of the Natural gas regenerative through furnace is friendly and easy for operators to use. At the same time, the equipment also has the function of fault diagnosis and alarm, which can find and deal with abnormal situations in time.

2. Rapid temperature rise

The Natural gas regenerative through furnace can heat the metal material to the required temperature in a short time, which improves the production efficiency.

3. Efficient combustion

The Natural gas regenerative through furnace adopts advanced combustion technology and control system, which can realize full combustion of natural gas and improve combustion efficiency. At the same time, some equipment is also equipped with waste heat recovery system, which can further recycle the waste heat in exhaust smoke and improve energy utilization efficiency.

4. Extend the service life of equipment

The Natural gas regenerative through furnace adopts advanced combustion technology and materials, which has a long service life and low maintenance cost.

5. Wide application range

The Natural gas regenerative through furnace is suitable for forging and heating of various metal materials, including steel, aluminum and copper. At the same time, it can also be used in metal heat treatment, tempering and other technological processes.

Natural gas regenerative through furnace

5、Advantages of Natural gas regenerative through furnace principle

Natural gas regenerative through furnaceat runtime,The high-temperature flame and flue gas generated when fuel (natural gas) burns in the furnace are used as heat sources to heat the medium flowing in the tube to reach the specified process temperature.，It is a product series that integrates Metal melting and casting, Energy conservation and environmental protection, Metal tempering, Energy conservation and environmental protection and Metal forging heating。

Natural gas regenerative through furnace

6、Natural gas regenerative through furnace characteristics

The Natural gas regenerative through furnace features are as follows:

1. Easy to control

The combustion system and ventilation system of the Natural gas regenerative through furnace can be adjusted as required to accurately control the temperature and atmosphere in the furnace and meet the heating requirements of different metal materials.

2. Strong adaptability

The Natural gas regenerative through furnace can be used for forging and heating of bar, round steel, square steel, steel plate and other metal materials, and has a wide range of applications.

3. Efficient heating

The Natural gas regenerative through furnace can heat the metal material to the required temperature in a short time and improve the production efficiency.

4. Easy to maintain

The structural design of the Natural gas regenerative through furnace is reasonable and easy to maintain, which reduces the operating cost and failure rate of the equipment.

5. Stable and reliable

The Natural gas regenerative through furnace has a stable combustion system and temperature control system, which can ensure the uniformity and stability of the temperature in the furnace, thus improving the quality and production efficiency of forged products.

Natural gas regenerative through furnace

Natural gas regenerative through furnaceusually used in war industry, machinery, building materials, automobile, chemical industry and other fields，is a kind of high quality and low price Natural gas regenerative through furnace，It can be used for Metal heat treatment, Metal tempering, Metal tempering, Metal forging heating, Metal heat treatment, Improve production efficiency and so on。