Introduction to Car mold preheating furnace and forging furnace working principle

Car mold preheating furnaceIt is an important heating equipment before metal forging. It uses natural gas as fuel to heat metal materials through high-temperature flame and smoke generated by combustion to meet the requirements of forging process.。

1、Brief introduction of Car mold preheating furnace

Car mold preheating furnaceIt is a forging heating device using gas as fuel.，It has the functions of Metal melting and casting, Metal tempering, Improve production efficiency, Metal forging heating and Energy conservation and environmental protection，is a popular Car mold preheating furnace，at work,Heat of combustion based on fuel. Natural gas is sprayed from the burner, mixed with combustion-supporting air and burned to produce high-temperature flame and smoke. These high-temperature flames and smoke transfer heat to the metal materials in the furnace by radiation and convection, so that they gradually heat up to the temperature required for forging.，it is an ideal choice for customers to buy Car mold preheating furnace。

Car mold preheating furnace

2、Physical picture of Car mold preheating furnace

Its appearance design is exquisite and elegant. The following is a high-definition picture of the factory for One-combustion energy saving's customers to choose and buy. You can contact online customer service at any time, make an appointment to visit the factory and take a shuttle bus from One-combustion energy saving.。

Car mold preheating furnace

Note: All the pictures in this article were taken by One-combustion energy saving manufacturer.。

3、Structural characteristics of Car mold preheating furnace

The Car mold preheating furnace has the following structure

1. Radiation chamber

The heat load of the main place for Car mold preheating furnace heat exchange accounts for about 70%-80% of the whole furnace. The furnace tube in the radiation room conducts heat through flame or high-temperature flue gas, which is mainly radiant heat, so it is called radiation tube.

2. ventilation system

Ensure the gas flow in the furnace and maintain the stability of the atmosphere and temperature in the furnace.

3. combustor

The device that mixes natural gas with combustion-supporting air and ejects it is the core component of the heating furnace.

4. Waste heat recovery system

Recover the waste heat in the exhaust gas of heating furnace to improve the energy utilization efficiency.

5. convection chamber

The high-temperature flue gas discharged from the radiation chamber is used for convective heat transfer to further heat the metal materials.

Car mold preheating furnace

4、Advantages of Car mold preheating furnace principle

Car mold preheating furnaceat the start of the operation,The high-temperature flame and flue gas generated by burning gas (such as natural gas and liquefied petroleum gas) in the furnace are used as heat sources to heat metal materials.。

Car mold preheating furnace

5、Car mold preheating furnace use

The purpose of Car mold preheating furnace is introduced as follows:

1. Metal melting and casting

Although it is mainly used for forging heating, some types of Car mold preheating furnaces can also be used in metal melting and casting processes. This is especially suitable for melting and casting of small or special alloys.

2. Energy conservation and environmental protection

The Car mold preheating furnace uses clean energy as fuel, which has lower emissions and higher energy efficiency than traditional coal-fired or oil-fired stoves. This is helpful to reduce environmental pollution and realize green production.

3. Metal forging heating

The Car mold preheating furnace can heat the metal material to the temperature required for forging, improve its plasticity and fluidity, and thus facilitate forging. This is very important for the forging of various metal materials.

4. Metal tempering

By properly heating and cooling the metal material, the Car mold preheating furnace can realize the quenching and tempering treatment of the metal. This is helpful to adjust the hardness and toughness of metal to meet the needs of different workpieces.

5. Metal heat treatment

In addition to forging heating, Car mold preheating furnaces can also be used for metal heat treatment processes, such as annealing and tempering. These processes can improve the microstructure and properties of metal materials, and improve their service life and mechanical properties.

Car mold preheating furnace

Car mold preheating furnacethe main features are Strong adaptability, Easy to maintain, energy saving and environmental protection, Strong adaptability and Easy to control，it is widely used in petroleum, aerospace, automobile, surface treatment, pharmacy and other industries。